'Glass Security Bulletproof Film for window and door protection'
Your Safety Is Our Promise!
The Best Glass Security Bulletproof Film in ASIA
An ULTIMATE QUALITY Products.
Security film means a layer of film where you install on glass window or door to protect glass from breaking into pieces by hard object knock either by hand or natural disaster. In any incident, the glass will breaks but security film withhold the glass all together from breaking into pieces and prevent penetration. (Back to TOP)
Bulletproof film is a tougher and stronger film with special material to withstands Bullet penetration.
The basic one layer of bulletproof film with 8 ~ 10mm glass thickness can withstands light pistol with bullet traveling speed between 300 ~ 400 m /s. With additional glass layer and film, it can withstands higher armor or higher speed traveling bullet such as AK47, M60, Machine Gun, etc...(Back to TOP)
Bulletproof glass is a sandwiched of 2 pieces of glasses with the film in between. The sizes of the glass is quite standard or require custom make according to orders. It requires thicker glass to withstands bullet if compare with bulletproof film.
Moreover, bulletproof glass require a skill technical team to install, heavier in weight and much more expensive than bulletproof film. In installation of bulletproof glass on existing building, it requires heavy renovation and the whole window or door frame need to be change to suit the bulletproof glass thickness. Where bulletproof film can be installed in existing glass without the need to change the glass or frame. (Back to TOP)
Security and Bulletproof film comes with GLUE layer. Where user can peel off the protection sheet and stick the film on the glass surface. Prior cleaning of glass surface with mild soap water and clean water is require to prevent poor adhesion.
Film need to be cut according to glass dimension before installing. Film can be cut by normal stationary blade. (Back to TOP)
During installation of film on glass surface, water is use to provide flexibility during installation. Thus water moisture and air bubble is captured between glass layer and film.
To have it 100% effective, the water moisture between the glass and film needs to be totally dry off and allow glue layer to stick hard on glass. In normal condition or room temperature, it requires at least 21 ~ 30 days for total dry up. (Back to TOP)
In installation of the film, you would require:
* Water sprayer
* Stationary blade
* Water wiper to remove water and air bubble
* Hard and flat surface rubber scrubber to remove balance of captured tiny water moisture and air bubble.
* Clean cotton cloth
* For more information and learning skill, check out with your local solar film installer.
STEC has 3 types of security film, 112c, 224c and 336c.
112c = 112 micron / 0.112mm
224c = 224 micron / 0.224mm
336c = 336 micron / 0.336mm
224c is the recommended security film for high protection against break in either by heavy knock by hard object or bar hand.
STEC also has color 224 level for choice, GREG, GREEN and Bronze. (Back to TOP)
Yes, only basic knowledge require. To learn on film installation, please consult tinted or solar film installer at local retail near you. (Back to TOP)
5 years warranty on film property. (Back to TOP)
Security film is tough enough to withstand any great impact with may penetrate the glass. Thus, with security film on glass, you do not need other glass protection material. (Back to TOP)
No...security and bulletproof film need to cover the whole glass without any punctual on its combination strength. (Back to TOP)
No need....security and bulletproof film only need to install on the visible surface of glass, Does not need to dismantle the frame to install the film. But the glasses require frame to whole the glass, security and bulletproof will be weaken if install on glasses without any frame. (Back to TOP)
You just need to use Glass Sealant or Silicon Glue to add additional glass on the existing glass. Seal the additional glass by the edge, all round and not the whole glass surface. (Back to TOP)
Price: STECglass Bulletproof film is the cheapest in market as it's produced in Asia, lower labor cost and overhead if compare with those made in USA or Europe. (Back to TOP)
Better Quality: STECglass Bulletproof film is tested, approved and use by Military and Navy to protect Weapons room, battle ship window and others. Thus, it is design not only to withstands normal disaster or man-made but to withstands high level impact which required by the Military standard. (Back to TOP)
Yes, it can be installed on Vehicle glasses. (Back to TOP)
Width - 1524mm
Length: 30 meters.
Weight: 30kg ~ 50kg / roll depends on types.
The above is our standard film dimension. OEM or special request dimension can be made with minimum order of 200 rolls for each type. (Back to TOP)
Please check out detail specification here.
A slight glue stain will be on the glass, you can clean it with soap water with flat stationary blade. If too hard, use alcohol or petrol. No odor on glass. (Back to TOP)
No, after dismantle or peel off, the glue layer will be damaged and cannot be used again. During peel off, the property of the film will be damaged as well. (Back to TOP)
Yes, because there is still water moisture in between the glass and film. It requires at least 30 days in total cure at room temperature. (Back to TOP)
Yes, expose the glass to Sun ray with good ventilation after installation. This will shorten the cure by 5 ~ 7 days. Do not use any hair dryer or heat generating equipments to dry off the surface, this will damage the film property. (Back to TOP)
Distributor are requested to buy sample in standard roll for test.
STEC will not provide or supply loose film or cut film as the films require packaging protection and intelligent property protection. This is our standard policy. (Back to TOP)
20 ~ 30 days of production time. (Back to TOP)
Our capacity in production and minimum production is 250 rolls / day. (Back to TOP)
Please write to us and check whether the distributorship for your area has been taken or still available.
Contact us at: firstname.lastname@example.org.
Please write to us for further discussion at: email@example.com
As our standard roll dimension is 1.524mm x 30 meter, please divide it to the total glass dimension on the vehicle
with an allowance of 10 ~ 15% for wastages at corner or shape forming. (Back to TOP)
Any other questions are welcome. Please send your questions to: firstname.lastname@example.org.